FMG - FMT-LX - Turbine Meters
The FMT-Lx series turbine meter is a robust meter, designed to perform on the highest level of accuracy. The meters comply with all international standards and are approved for custody transfer. The actual flow sensor, an exchangeable cartridge, has a build-in multi stage flow conditioner enabling the meter to be installed without any straight in- and outlet sections. All tested and proved according perturbation test as per international standards.
The cartridge can be pre-calibrated, under both low and high pressure conditions, then exchanged on-site. The cartridge is supported in O-rings and isolated from the body, hence unaffected by any influences of the housing. The short length cartridge enables the use of larger sized cartridges than the size of the meter body. The approved maximum capacities of these kind of meters are extremely high and similar to the capacities of ultrasonic meters.
To reduce transportation cost, optimize the corrosion protection and improve safety in handling, the FMT-Lx series of turbine meters up to 6’’ (DN150) are also available with low weight aluminium meter bodies.
Product DATASHEET - FMT-LX Series Turbine Gas Meters
Principle
The operation of the FMT series of turbine meter is based on the measurement of the velocity of gas. The flowing gas is accelerated and conditioned by the integrated multi stage flow conditioner. The multi stage flow conditioner prepares the gas flow profile by removing undesirable swirl and asymmetry before the gas flows over the freely rotating turbine wheel
The dynamic forces of the flowing gas cause the rotor to rotate. The turbine wheel is mounted on the main shaft, with high-precision, low-friction ball bearings.
The turbine wheel has helical blades that have a known angle relative to the gas flow. The gas flow drives the turbine wheel at an angular velocity, which is proportional with the gas velocity. Using a gearing mechanism, the rotating turbine wheel drives the mechanical counter.
Applications
The standard FMT-Lx turbine meter is suitable for custody transfer gas measurement of all non-corrosive gases such as natural gas, propane, butane, air, nitrogen, hydrogen, etc. for low and high operating pressures.
Special constructions can be supplied for use under extreme condition like high temperatures or corrosive gases. The FMT-Lx can be modified to perform as a master meter or transfer master meter.
Main Features
- Flow range 3- 40.000 m3/h
- Diameters DN50 - DN600 (2” - 24”)
- Pressure rates PN 10 - 100, ANSI 150 - 600
- Compliant with EN12261:2002
- Compliant with EN12261:A1-2006
- Compliant with OIML R137 1&2 (2014)
- Compliant with MID 2014/32/EU
- MID temperature range -25 to +70ºC
- Length 3x DN
- Removable meter cartridge
- No straight inlet/outlet sections required
- Oil flushing and lubrication system
- Multipurpose exchangeable index
- Tamper proof IP67 sealed index
- Special meters on request
- Seals according EN 549 (seals for gas appliances and gas equipment)
Technical Specification
Metrological approvals: Compliant with EN12261:2002
Compliant with EN12261:A1-2006
Compliant with OIML R137 1&2 (2014)
Compliant with MID 2014/32/EU
ATEX approvals: Sensors compliant with Ex ia IIC T4... T6 Gb (-40ºC ≤ Ta +70ºC)
Encoder compliant with Ex ib IIB T3... T6 Gb (-25ºC ≤ Ta +55ºC)
Flow rates: 3 m3/h up to 40.000 m3/h
Nominal diameters: From DN50 to DN600 mm (2” to 24”).
Mounting position: Horizontally or vertically
Body: Compliant to Pressure Equipment Directive 2014/68/EU
Temperature Range: ATEX: -25°C to +70°C
MID: -25°C to +70°C (lower temperatures on request)
PED: -20°C to +70°C (lower temperatures on request)
Materials
Body (Standard): Low weight aluminium / steel
Body (Optional): Low temperature steel
Cartridge: Aluminium
Straightening vane: Aluminium
Turbine wheel: Aluminium
Bearing block: Stainless steel / aluminium
Bearings: Stainless steel
Shafts: Stainless steel
Gears: POM
Index frame: Aluminium
Index cover: PolycarbonateECI
Typical metrological characteristics
Accuracy 0,2 Qmax to Qmax: ± 1% or better
Accuracy Qmin to 0,2 Q max: ± 2% or better
Repeatability: better than 0,1%
FMG Gas Meters FMT-LX series are NMIM certified by SIRIM and also certified by NMI International.